public:mdvr:mdvr_quit_start_by_cp4_or_monitor

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
public:mdvr:mdvr_quit_start_by_cp4_or_monitor [2020/10/20 11:21]
europe 		public:mdvr:mdvr_quit_start_by_cp4_or_monitor [2021/08/20 08:51] (current)
europe ↷ Page moved from mdvr:mdvr_quit_start_by_cp4_or_monitor to public:mdvr:mdvr_quit_start_by_cp4_or_monitor
Line 99: Line 99:
  
 The MDVR can automatically load the access IPC. But sometimes the IPC address is modified manually, manual installation is required.  The MDVR can automatically load the access IPC. But sometimes the IPC address is modified manually, manual installation is required. 
-1)Go to the page “Surveillance -> IPC Setup” and chose the Channel 1&2; +  -   Go to the page “Surveillance -> IPC Setup” and chose the Channel 1&2; 
-2)You should choose Channel 1&2 on the left side and click the “Search” button; +  -   You should choose Channel 1&2 on the left side and click the “Search” button; 
-3)Add the specific IPC remote and save the configure; +  -   Add the specific IPC remote and save the configure; 
-4)Click the “Outside” button and save your configure; +  -   Click the “Outside” button and save your configure; 
-5)Back to the beginning interface, then you will see the display from your cameras.+  -   Back to the beginning interface, then you will see the display from your cameras.
 Step1-Step5 as follow: Step1-Step5 as follow:
    
Line 139: Line 139:
 Notice: Notice:
 If you set up an MDVR with HDD or SD to record, you can playback the video on the Playback page and export the video to the U disk. Follow the steps below: If you set up an MDVR with HDD or SD to record, you can playback the video on the Playback page and export the video to the U disk. Follow the steps below:
-1)Click the Next button, you can select which channel to playback; +  - Click the Next button, you can select which channel to playback; 
-2)Click the Search button to go to set the start time to playback; +  - Click the Search button to go to set the start time to playback; 
-3)Click the Playback button to playback. Click the Export button to export the video to the U disk. If you are exporting video, you need one more step to set the end time. +  - Click the Playback button to playback. Click the Export button to export the video to the U disk. If you are exporting video, you need one more step to set the end time. 
-4)The U disk must format to FAT32 before export video from your computer or on the MDVR storage page and ensure that the available capacity of the U disk is larger than the exported video data size.+  - The U disk must format to FAT32 before export video from your computer or on the MDVR storage page and ensure that the available capacity of the U disk is larger than the exported video data size.
  
 ==== Configure Video & Record ==== ==== Configure Video & Record ====
Line 154: Line 154:
 === Alarm linkage video screen configure === === Alarm linkage video screen configure ===
  
-If you need to display the reversing video screen when you are reversing or the left/right video screen when you are left/right steering on your monitor, access the reversing/left steering/right steering signal to MDVR and follow the steps bellow to set : +If you need to display the reversing video screen when you are reversing or the left/right video screen when you are left/right steering on your monitor, access the reversing/left steering/right steering signal to MDVR and follow the steps below to set : 
-1)Go to page “Collection -> General -> Sensor”; +  -   Go to page “Collection -> General -> Sensor”; 
-2)Select the I/O Number what’s the trigger signal wired; +  -   Select the I/O Number what’s the trigger signal wired; 
-3)Select the Trigger Source, it can support Voltage or Pulse; +  -   Select the Trigger Source, it can support Voltage or Pulse; 
-4)Select the Sensor Uses to Reversing\Left Steering\Right Steering; +  -   Select the Sensor Uses to Reversing\Left Steering\Right Steering; 
-5)Go to page “Alarm -> Base -> IO Alarm”; +  -   Go to page “Alarm -> Base -> IO Alarm”; 
-6)Select the Sensor number what’s the trigger signal accessed; +  -   Select the Sensor number what’s the trigger signal accessed; 
-7)Click the Setup button under the column Linkage to enter Setup page; +  -   Click the Setup button under the column Linkage to enter Setup page; 
-8)Set the Linkage Screen to “Single” or “Quad” and select channel; +  -   Set the Linkage Screen to “Single” or “Quad” and select channel; 
-9)Click the Save button to save.+  -   Click the Save button to save.
    
 {{:mdvr:pasted:20201020-105646.png}} {{:mdvr:pasted:20201020-105646.png}}
Line 205: Line 205:
  
 You can get all of the firmware version on the page “System->Version info”, it includes: You can get all of the firmware version on the page “System->Version info”, it includes:
-1)Device ID corresponding the MDVR Device ID; +  -   Device ID corresponding the MDVR Device ID; 
-2)Serial Num corresponding the MDVR Serial number; +  -   Serial Num corresponding the MDVR Serial number; 
-3)MAC Address corresponding the MDVR MAC address; +  -   MAC Address corresponding the MDVR MAC address; 
-4)Firmware Version corresponding the MDVR firmware version; +  -   Firmware Version corresponding the MDVR firmware version; 
-5)MCU Version corresponding the MCU firmware version; +  -   MCU Version corresponding the MCU firmware version; 
-6)CP3/4 Version corresponding the CP3/4 firmware version.+  -   CP3/4 Version corresponding the CP3/4 firmware version.
  
 ==== Upgrade ==== ==== Upgrade ====
Line 216: Line 216:
  
 Basic prepare: Basic prepare:
-1)U disk format to FAT32. +  -   U disk format to FAT32. 
-2)New a folder named “upgrade”. +  -   New a folder named “upgrade”. 
-3)Copy the upgrade file into the folder. Make sure there is only one upgrade file in the folder. +  -   Copy the upgrade file into the folder. Make sure there is only one upgrade file in the folder. 
-4)Plug in the U disk into the USB port in front of the MDVR.  +  -   Plugin the U disk into the USB port in front of the MDVR.  
-Device & CP4 & IPC & GPS upgrade+ 
 +=== Device & CP4 & IPC & GPS upgrade === 
 You can upgrade all of the firmware version on the page “Setup->Maintenance->Upgrade”, click the corresponding “Upgrade” button on the right. It includes: You can upgrade all of the firmware version on the page “Setup->Maintenance->Upgrade”, click the corresponding “Upgrade” button on the right. It includes:
-1)Device upgrade, CP4 upgrade, IPC upgrade, GPS upgrade; +  -   Device upgrade, CP4 upgrade, IPC upgrade, GPS upgrade; 
-2)Because you may have more than one IPC, you need to select which one to upgrade firstly on the page which you click the “upgrade” button on the right to enter.+  -   Because you may have more than one IPC, you need to select which one to upgrade firstly on the page which you click the “upgrade” button on the right to enter.
  
 {{:mdvr:pasted:20201020-105956.png}} {{:mdvr:pasted:20201020-105956.png}}
Line 233: Line 235:
  
 Basic prepare : Basic prepare :
-1)U disk format to FAT32; +  -   U disk format to FAT32; 
-2)Plugin the U disk into the USB port in front of the MDVR.+  -   Plugin the U disk into the USB port in front of the MDVR.
 Notice:  Notice: 
 The configure files can’t import & export between different firmware version or MDVR model. The configure files can’t import & export between different firmware version or MDVR model.
-Export & Import configure file+ 
 +=== Export & Import configure file === 
 You can export or import configure file on the page “Setup->Maintenance->Config”, click the “Export” or “Import” button on the right according to your needs. You can export or import configure file on the page “Setup->Maintenance->Config”, click the “Export” or “Import” button on the right according to your needs.
  
 {{:mdvr:pasted:20201020-110034.png}} {{:mdvr:pasted:20201020-110034.png}}
    
-Default all settings to the factory state+=== Default all settings to the factory state === 
 You can default all settings on the page “Setup->Maintenance->Reset”, click the “Reset” button on the right. You can default all settings on the page “Setup->Maintenance->Reset”, click the “Reset” button on the right.
 Notice:  Notice: 
Line 254: Line 259:
  
 The device stores the log information related to operation in the record media(HDD or SD), it can be covered automatically when the storage is full or deleted by formatting. Sometimes we can export it to analyze the reason of some problems on the page “Setup -> Maintenance->FileData”. The log includes: The device stores the log information related to operation in the record media(HDD or SD), it can be covered automatically when the storage is full or deleted by formatting. Sometimes we can export it to analyze the reason of some problems on the page “Setup -> Maintenance->FileData”. The log includes:
-1)Alarm log, alarm information e.g. Overspeed alarm; +  -   Alarm log, alarm information e.g. Overspeed alarm; 
-2)Operation log, information of device running, e.g. power-on time, version, network status; +  -   Operation log, information of device running, e.g. power-on time, version, network status; 
-3)You can export all of the logs if you didn’t know when the problem happened or export the log of the specific date if you know the date.+  -   You can export all of the logs if you didn’t know when the problem happened or export the log of the specific date if you know the date.
      
 {{:mdvr:pasted:20201020-110142.png}}  {{:mdvr:pasted:20201020-110142.png}} 
Line 264: Line 269:
 {{:mdvr:pasted:20201020-110208.png}} {{:mdvr:pasted:20201020-110208.png}}
    
-4)Because the USB port on the device is occupied by the mouse when you want to export operation log or alarm log, you can use the following two methods: +  - Because the USB port on the device is occupied by the mouse when you want to export operation log or alarm log, you can use the following two methods: 
-a)Prepare a USB hub so that you can connect the mouse and U disk at the same time and export the log to the U disk; +  * a)Prepare a USB hub so that you can connect the mouse and U disk at the same time and export the log to the U disk; 
-b)Prepare a network cable and a computer. The cable connects the computer to the device; +  * b)Prepare a network cable and a computer. The cable connects the computer to the device; 
-c)Through the display screen connected to the device，on the page “basic setup->local->network”，check the IP Address.+  * c)Through the display screen connected to the device，on the page “basic setup->local->network”，check the IP Address. 
  
 {{:mdvr:pasted:20201020-110257.png}} {{:mdvr:pasted:20201020-110257.png}}
-  + 
-d) Check if the network segment on the computer matches the IP address of the device.+  * d)Check if the network segment on the computer matches the IP address of the device.
  
 {{:mdvr:pasted:20201020-110311.png}} {{:mdvr:pasted:20201020-110311.png}}
Line 284: Line 290:
  
 Sometimes we need to get more details of device’s running, we have to get the print log by U disk follow below: Sometimes we need to get more details of device’s running, we have to get the print log by U disk follow below:
-1)U disk format to FAT32; +  -   U disk format to FAT32; 
-2)Copy the file “n9m_print_cfg” into the U disk. No folder needed, just in the root of the U disk. Make sure every letter of the file name is the same as “n9m_print_cfg” and the U disk has no file named “all”; +  -   Copy the file “n9m_print_cfg” into the U disk. No folder needed, just in the root of the U disk. Make sure every letter of the file name is the same as “n9m_print_cfg” and the U disk has no file named “all”; 
-3)Plugin the U disk into the USB port in front of the MDVR; +  -   Plugin the U disk into the USB port in front of the MDVR; 
-4)Run the device until the problem appears; +  -   Run the device until the problem appears; 
-5)Remove the U disk from the device, and then restart the device to exit the log mode; +  -   Remove the U disk from the device, and then restart the device to exit the log mode; 
-6)Plugin the U disk to the computer and cut the file “all” to the computer, and then send it to our technical support. +  -   Plugin the U disk to the computer and cut the file “all” to the computer, and then send it to our technical support. 
 +  - 
 {{:mdvr:pasted:20201020-110449.png}} {{:mdvr:pasted:20201020-110449.png}}
    
      
  • public/mdvr/mdvr_quit_start_by_cp4_or_monitor.1603185679.txt.gz
  • Last modified: 2020/10/20 11:21
  • by europe